Viva Mar

TECHNICAL SPECIFICATION

• After completion of Building Foundations excavation, Sub – Foundation gritting shall be made. Spread – based water shall be applied from foundation and above – foundation shall be added to foundation alum and above which the concrete leveling concrete shall be laid.
• Prior to constructing the refilling around the building all waste water installation shall be laid and concrete drainages shall be built at necessary regions and the drainage chutes through which the drain flex pipes around the foundation of the building shall have been completed and required compression shall be ensured by means of irrigation of refilling made.
• With all reinforced concrete dies of building constructions made, including foundation, 18 mm Water Proof ply wood has been used and their reinforcements shall have been completed with the tie rods and all concreting works made shall make it possible to apply the most powerful vibrators to compress them as required.
• The foundation, flood stage and story sheet concreting of all buildings shall have been laid by concrete with additive and all concrete structures laid shall have been vibro – compressed and thus homogenous spread of concrete shall be ensured. Concrete sapling shall be applied from all concrete structures made and C20 Concrete quality shall be ensured prior to concrete pouring work. By being regularly watered, it shall be assured for the entire concrete structures made to acquire resistivity.
• With all manufactures made, the irons from the static project shall have been tied and all entry repetitions, entry hooks and mackerel irons shall be employed as shown in their project. From all reinforced concrete manufactures, special plastic reinforced – concrete raisers and their contet with water and air shall be prevented by stressing on employing raisers strictly. This is very important in respect of concrete life span.
• The outer walls of the buildings shall be laid in form of a specially manufactured Sandwich type of brick wall and outer walls shall be laid in 25 – cm thickness and inner wall in 10 – cm thickness.

The properties of Sandwich – type brick wall: Sandwich – type brick wall consisted of brick in 13,5 cm thickness and 3 cm polystyrene foam and 8,5 cm inner brick ensures the Heat an Audio insulation and is flame and humidity – resistive.

• Prior to laying the outer walls of the buildings, cement – based 1 st class spreadible water insulation material shall be applied on the floom concrete. Alongside all walls and girder juncture lines, a sound durability of the walls shall have been ensured as a result of expansion of polystyrene foam sprayed between the concrete the wall. This operation prevents at a great scale, the cracks which might take place due to ground vibrations in future.
• The lintels of door and window shall be cast in site and the lentils shall be cast as having been tied by adequate number of lentils with wide above – door opening formed by iron cage tied with entries.
• The flood stage sheets of the building shall have been insulated, by 1 st Class composite, fully elastic water insulation material. The insulation material shall be applied in form of two layers onto the surface made dust free through flushing and the reinforcement where necessary, shall be made by equipment netting.
• All Sanitary Installation pipes and fittings shall be Ege or Fırat Plastic products and particularly for the vertical piping passed through wall, embedded wall channels shall be used and the channels shall be closed by mortar after the pipes are laid. Similarly, the piping network passing over the floor shall be protected by being covered with mortar after having been laid. Upon having completed laying work of all installations, pressure test shall be performed, to see if there exists any water leakage.
• At all buildings, due care shall be paid for equal energy distribution using triphase Electricity lines. Wiring shall be accomplished and outside the buildings. The conduits through which the cables shall be drawn shall be consisted of 32 atü pipes. As the electric cable, 1 st class TSE – certificated cable shall be employed. For the switches and outlet sockets (TSE – certificated brands shall be used. The special copper earting plates which are standard for all electric apparatus shall be made separately as per apart ent house. The Fuse Blocks and fuses shall be chosen form the TSE – certificated trademarks. All electrical installation shall be drawn without any junction boxes thus power and fuses be gathered at a sole center.
• Air Conditioning system at all apartment houses shall be made available for immediate installation.
• The outer plasters of the building shall be made by using a water insulating and adherence ensuring type of additive. The fine decorative plaster over coarse mortar shall be applied above the splashed mortar.
• The roof inclination alum shall be laid at its level and with necessary inclination alum shall be laid at its level and with necessary inclination and following the alum pouring, its surface shall be leveled by a tearfill trowel and a smooth surface shall be obtained.
• The joining works shall be Winsa, Pimapen, Egepen etc brand according to its project and in white PVC color. The glass of windows shall be of Isıcam 4 + 12 + 4. The access door of the apartment houses shall be steel door type.
• The finishing paints of acrylic type or silicon based outer frontal type shall be applied over the decorative building outer plaster other than natural stone coatings of the buildings.
• Air conditioning pipings shall be laid to the dining room and parents bed room from the apartment houses in a manner to allow installation and 1 each air conditioner shall be installed at every apartment house.
• The inclination alum at the roof terraces composite, full elastic water insulation material in double layers by a 1 st class, TSE – certificated composite, full elastic water insulation material in accordance with European norms. Equipment (riggin) netting shall be laid between the layers.
• The surrounding walls of the site in which totally 3 buildings consisting of 71 apartments houses (domiciles) are situated and its pool and the circumference of the pool shall be delivered as having been fully and completed landscape implementation.

FRAME CONSTRUCTION

• Reinforced Concrete in Carcase Form 
• Vibratory concrete pouring by plywood form system
• Using plastic raisers from all riggins.
• All outer walls (25 cm) laid as being heat and audio insulation, high quality Sandwich type brick wall.

WATER, HEAT AND AUDIO INSULATION

• All foundation concrete sheets as well as pool concretes with water impermeability additive.
• Spread – based Water Insulation on all foundation concretes
• 1 st Class UV – resistant, spread type Water Insulation on surface of all roof and parapets.
• 1 st Class Polystrene foam Heat Insulation at all roofs
• 1 st Class spread – type moisture resistant Water Insulation beneath all outer walls.
• 1 st Class, Sandwich Brick Wall with audio insulation feature at all outer walls.
• 1 st Class spread – type water insulation beneath all frontal stone coaings

DRAINAGE LINES

• Drainage lines under the building’s foundation and around the apartment.

OUTER FRONTAL SURFACE COATINGS

• 1 st Class having 5 Additives, water imperpeeability additive, adherence promoting feature, Interior and Exterior Plaster
• Plaster – made door, window and decorative frontal Frames
• Esthetic Bay – Windows and Stucco Fugas
• 4 layered Outer Frontal Paints with Silicon Grains (Primer, Grained Paints, Double – layered, colored silicon paints)

INNER FRONTAL SURFACE COATINGS

• Interior walls with 3 – layered plastered stucco
• Decorative niches at internal walls

JOINING WORKS AND ENTRANCE DOOR

• Outer Frontal PVC Joining Works manufactured by means of null electrode welding technology.
• Outer frontal windows with Isıcam
• Special Tresholds and Splays made of Travertin etc. beneath the joining works.

EMBEDDED AIR CONDITIONER, ELECTRICAL AND SANITARY INSTALLATIONS

• Outlet, swith sockets manufactured from durable Plastic.
• 1 st Clas Hes brand etc. electric cables.
• TSE – Certificated Fuse Blocks
• TV and Telephone Outlet as per Bed – room and Dining – room
• Adequate number of electricity outlet foreseen for all purposes at every space.
• Air Conditioner Installation at Dining Room and Parents Bedroom.
• Sanitary Piping made according to Standards.
• 1 st Class double – sealed, thick walled PVC pipes and Fresh Water Fittings
• Comfortable Bath rooms in respect to Lighting and Aeration
• Infrastructure System formed by Concrete Drainages and PVC pipes laid in cross sections in compliance with the Standards.

BUILDING OVERALL PROPERTIES

• Aluminum Terrace Safety Railings and Balcony Parapets

SITE PROPERTIES

• A 190 m² Pool belonging to the Site (5 different water sealed, illuminated and in compliance with the project)
• The coating of the pool shall be of BTB glass mosaic.
• Travertin Pool Circumference
• Common TV satellite system
• General use Site Water Tank

SITE DELIVERY DATE AND TITLE DEED INFORMATION

• The Site shall be completed in December 2008 with full operation and functional environmental landscape.
• All site buildings, exterior frontal joining works including entrance doors shall be accomplished at latest by December 2008
• Upon obtaining the construction license, story easement title deeds shall be made ready to allow immediate sale against title deed.
• The condominium title deeds shall also be obtained in December 2008 following immediately upon Building use license as a group

IN APARTMENT HOUSE FINE WORK MATERIALS AND DETAILS

Interior space manufacture items of the buildings, frame constructions and exterior fronts and landscapes and stone walls, pools of which are completed and types of materials to be used and their details are specified item – by – item below

• Apartment houses’s inner alums shall be in 10 – 12 cm thickness as to capsulate embedded floor piping networks with remarks
• Bath Vitrifications and Accessories and Batteries shall be of CEM or ECA brand.
• The Kitchens are calculated to be made from complete MDF laminated cupboards with profile door, laminated or marble kitchen counter and Standard TERRA NOVA or FRANKE Basin.
• Internal doors shall be manufactured as American Panel Doors.
• Electric Outlets and Switches are planned to be VIKO KARDELEN Series. At all spaces adequate number of earted outlets, TV outlets and Telephone Outlets at all bed rooms are considered to be installed, including dining rooms.
• Floor Coatings shall be of ceramic tiles.
• The wall covers shall be ceramic at wet spaces and three – folded plaster stucco and plastic paint thereon have been planned to be applied.
• At Inner spaces, the ceilings shall be plastered by fine stucco over rough plaster.
• It has been intended to be implemented a spread – type water insulation on all wet space floors and 30 cm walls.